PowerStream Power supplies, battery chargers, batteries and packs, dc/dc converters, injection molding    View Shopping Cart
June 3, 2024

Wall mount 1 cell Lithium-Ion and lithium-polymer chargers 2000 mA with universal AC input

Lithium-Ion Battery Pack Charger 3 cell pack
More Lithium Battery Chargers from PowerStream
Lithium-Ion Battery two cell charger

Lithium-Ion Battery Chargers for OEMs.


This battery charger is a microprocessor controlled unit designed exclusively for charging 1 cell 3.6 V or 3.7 V. Lithium-ion and lithium polymer (lipo, li-po, Li-poly) battery packs. It has led indicators to indicate the current operating mode of the charger. This battery charger complies with applicable safety agency requirements, and it is listed with UL, cUL and CE. This is an 4.2V peak battery charger.
This charger can also charge multi-cell packs when all the cells are in parallel. Such packs are 3.6V, but higher capacity than a single cell pack.
PST-P2012-L1 For charging 1 cell 3.6 volt lithium packs $24.00

add_to_cart.gif 
Quantity 1-9 10-49 50-99 100-499 500+
  $24.00 $21.00 19.65 $15.10 $12.75
plugset PST-WX12 ---- Output adapter barrel plug kit  $7.00
add_to_cart.gif
SDY-C53F (ZHJX002)
adapters with a barrel connector input and screw terminal output
For adapting the barrel connector to screw terminals $2.50 each
add_to_cart.gif
barrel connector alligator clip adapter Optional 18" alligator cord adapter $3.25
add_to_cart.gif

PST-P2012-L1 1 cell Pack Li-ion Battery Charger

       

NO

ITEM

UNIT

SPECIFICATION

REMARK

INPUT

       
 

Rating Input Voltage

V AC

100~240Vac 50/60Hz

 
 

Input voltage range

V AC

90~264Vac

 
 

Rating Input Current

A

0.2Arms

Test Conditions: INPUT: 220V OUTPUT: Full load

 

Max. input power

W

16

 

OUTPUT

       
 

Rating output voltage

V dc

4.2V

 
 

Output voltage range

V dc

3 VDC ~ 4.25 VDC

 
 

Suitable for Battery type

 

3.6V LI-ION or lithium polymer

 
 

Constant Charge current

A

2 A (+0.15A)

 
 

Constant Voltage

V

4.25 V (+-0.1V)

 
 

Charge end current

A

<0.1

 
 

Typical charge time

hour

1~1.5hours

Test Conditions:

For 2 Ah Li-ion pack

 

Max. output power

W

16.4 W

 
 

Hold-on time

ms

20

 
 

Ripple current

mA

50

Test Conditions:

Input: 220VAC Output: Full load

 

Charge finish condition

 

V > 4.2V + I<0.1A

 
 

LED color

 

Red: charging Green: finish/idle

 
 

Output short-circuit protect

 

Yes

 
 

Efficiency

%

>70%

Test Conditions:

At maximum load

Environment

       
 

Operate temperature

·C

-10 ~ +40

Full load & natural convection.

 

Operate humidity

%RH

< +90

Relative humidity, non-condensing.

 

Storage temperature

·C

-40 ~ +70

 
 

Storage humidity

%RH

0 ~ +95

Relative humidity, non-condensing.

 

Cooling

 

Natural convection

 
 

Temperature factor

%

   
 

Vibration resistance

 

5MM/50HZ/600S

Non-operating condition.

Mechanical

       
 

Weight

grams

120 grams

 
 

Size

mm

81 x 43 x 40 mm

Case only

 

Connectors

 

5.5 x 2.1 mm barrel, others available on special order in quantity, adapter plugs available (see below)

 
 

Impact resistance

 

1 meter drop test >= 3 times

Non-operating condition.

Safety

       
 

Max. temperature rise

·C

< 40 on casing

At any line and Max. Load

 

Safety standards

CE/cTUVus/PSE/CCC

Designed to GB4943 UL1950 EN60950

 
 

EMC standard

 

EN55022 B

 
 

MTBF

hours

30000

 
 

Limited power source

VA

50

 
 

ESD

kV

8.0

 
 

Hi-Pot Insulation

V

i/p to o/p: 3000 (1 min.)

For final unit, cut-off current =10mA


Twelve optional DC Plugs slip over the 5.5 x 2.1 mm connector if desired.
plugset
  • 2.35 OD x 0.7 ID Barrel
  • 3.0 OD x 1.1 ID Barrel
  • 3.5 OD x 1.35 ID Barrel
  • 4.0 OD x 1.7 ID Barrel
  • 4.75 mm OD x 1.75 mm ID Barrel EIAJ-03
  • 5.0 mm OD x 3.5 mm ID with center pin
  • 5.5 mm OD x 1.5 mm ID type 2 Barrel
  • 5.5 mm OD x 2.5 mm ID Barrel
  • 6.3 OD x 3.0 ID center pin Barrel
  • 6.0 OD x 4.4 ID center pin Barrel
  • 7.4 mm OD x 5.0 center pin ID Barrel
  • 7.9 OD x 5.6 ID center pin Barrel

Specifications:

OEM Battery Chargers Input Voltage: 100 - 240 VAC, 50/60 Hz.

OEM Battery Chargers Output Voltage: Up to 4.2 Vdc controlled by battery charger

OEM Power Supplies Output current: up to 1.2 A ±0.1 A maximum, controlled by battery charger

OEM Power Supplies Temperature: -10 to +45° C, Operating -40 to +70° C, non-Operating

Universal Power Input OEM Power Supplies and OEM Battery Chargers Humidity: Indoor 90% R.H. @ 35° Celsius, Non-Condensing


[Home] [PowerStream] [Site Map]
[Tech Resources]
[Policy and Privacy] [Contact Us]

Thank you for considering PowerStream

1 cell lithium ion and li-po battery pack charger , one cell lithium pack charger, 4.2V lithium battery charger

PowerStream Technology
1163 South 1680 West
Orem, Utah 84058
USA

Phone: 801-764-9060
Fax: 801-764-9061

© Copyright 2000, 2002, 2003, 2004, 2005, 2006, 2008,2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022
Lund Instrument Engineering, Inc. All rights reserved.

Google Author Verification